Sorry, but this only applies to drills and sanding machines. Maybe a bench grinder also you can cheap out on. Hand tools are fine to cheap out on also.
Any spinning blade, if you cheap out, don’t be surprised if you get life-alteringly injured when you “use it enough to break it”. I was just helping some friends renovate where they had a dirt cheap miter saw and it was just about the most dangerous experience of my life.
If you are doing any big renovations, at least get makita, Milwaukee, or dewalt. You can get a TON of cheaper stuff second hand. Quality at a lower price. I got a professional older model hilti hammer drill at a tiny fraction of the price.
I grew up using only quality tools, because cheap tools were truly shit until perhaps the 90’s, at the earliest.
HF tools used to be utter shit, but their “branded” tools are good these days. The wrenches and sockets are as good a Craftsman used to be, and equal to the store brands from Home Depot and Lowes. And overpriced Matco/Snap On can kiss my ass. I have some of their tools, they’re nice, but not worth the price.
Their branded cordless tools are good too. One thing they do differently is put the battery controller in the tool, while Milwaukee puts one in the battery. So don’t do anything foolish with the battery.
I don’t think they’re as durable as Milwaukee, the plastic seems harder, so more prone to cracking. And the warranty isn’t very long.
But with the massive cost difference, it’s a good place to start.
But exactly, that is the difference between a drill and spinning sharp metal at high speeds.
If a drill breaks, it isn’t going to send shards of metal-cutting fiber disc 20 meters per second at your face.
If a saw sucks ass like the one I used a few days ago, you can’t safely cut through wood and you end up doing dangerous things like putting your body weight on the top of the miter saw to get it down all the way, gripping the piece closer to the blade to try to get it to cut better with less tear out or to not slip, etc… which can easily lead to a finger being cut off. It is MUCH more expensive in the US especially to have to deal with a dismembered finger than the cost difference between a chinese amazon $100 miter saw and $200 entry level 10 inch dewalt.
There are a ton of people who can’t afford that. That is fine. Then spend $100 on good quality assorted hand saws. a $40 japanese pull saw, $30 for a Spear & Jackson hand saw, $40 for a pair of bacco chisels, and an angle cut box and you can do a lot more than that $100 miter saw much more safely at the cost of it being at half the speed.
If a saw sucks ass like the one I used a few days ago, you can’t safely cut through wood and you end up doing dangerous things like putting your body weight on the top of the miter saw to get it down all the way, gripping the piece closer to the blade to try to get it to cut better with less tear out or to not slip, etc…
There is a big difference between cheaping out on blades/never replacing them and cheaping out on the saw itself. I agree I wouldn’t get the absolute cheapest miter saw, but a relatively cheap one with good blades that are replaced often shouldn’t be significantly more dangerous than a more expensive one.
Sorry, but this only applies to drills and sanding machines. Maybe a bench grinder also you can cheap out on. Hand tools are fine to cheap out on also.
Circular saw, table saws, miter saws, angle grinders, etc…
Any spinning blade, if you cheap out, don’t be surprised if you get life-alteringly injured when you “use it enough to break it”. I was just helping some friends renovate where they had a dirt cheap miter saw and it was just about the most dangerous experience of my life.
If you are doing any big renovations, at least get makita, Milwaukee, or dewalt. You can get a TON of cheaper stuff second hand. Quality at a lower price. I got a professional older model hilti hammer drill at a tiny fraction of the price.
It really depends anymore…it can be a tough call.
I grew up using only quality tools, because cheap tools were truly shit until perhaps the 90’s, at the earliest.
HF tools used to be utter shit, but their “branded” tools are good these days. The wrenches and sockets are as good a Craftsman used to be, and equal to the store brands from Home Depot and Lowes. And overpriced Matco/Snap On can kiss my ass. I have some of their tools, they’re nice, but not worth the price.
Their branded cordless tools are good too. One thing they do differently is put the battery controller in the tool, while Milwaukee puts one in the battery. So don’t do anything foolish with the battery.
I don’t think they’re as durable as Milwaukee, the plastic seems harder, so more prone to cracking. And the warranty isn’t very long.
But with the massive cost difference, it’s a good place to start.
But exactly, that is the difference between a drill and spinning sharp metal at high speeds.
If a drill breaks, it isn’t going to send shards of metal-cutting fiber disc 20 meters per second at your face.
If a saw sucks ass like the one I used a few days ago, you can’t safely cut through wood and you end up doing dangerous things like putting your body weight on the top of the miter saw to get it down all the way, gripping the piece closer to the blade to try to get it to cut better with less tear out or to not slip, etc… which can easily lead to a finger being cut off. It is MUCH more expensive in the US especially to have to deal with a dismembered finger than the cost difference between a chinese amazon $100 miter saw and $200 entry level 10 inch dewalt.
There are a ton of people who can’t afford that. That is fine. Then spend $100 on good quality assorted hand saws. a $40 japanese pull saw, $30 for a Spear & Jackson hand saw, $40 for a pair of bacco chisels, and an angle cut box and you can do a lot more than that $100 miter saw much more safely at the cost of it being at half the speed.
There is a big difference between cheaping out on blades/never replacing them and cheaping out on the saw itself. I agree I wouldn’t get the absolute cheapest miter saw, but a relatively cheap one with good blades that are replaced often shouldn’t be significantly more dangerous than a more expensive one.