Does this ridiculous number of antennas even do anything or is it just marketing wank?
Technically, it does provide better connection speeds by enabling the router to avoid channel hopping, so it can talk to multiple devices (or the same devices if it has multiple antennae) at the same time. This is part of the recent wifi6 and wifi7 standards so more and more devices will start to gain speeds using this technique
Realistically computers have at best 2 antennae and this is largely marketing wank.
Though if you have multiple devices all trying to connect to wifi, like even a phone for example, then a computer having two antenna that it can actually use 100% of the time still sounds valuable to me.
Lord Sauron would like a word.
I’m a network professional with a specialty in wireless.
Yeah, beam forming and mimo are the main reasons for antenna diversity. There’s also more radio chains in those units typically, and more radio chains can provide better speeds if you have client devices that can take advantage of the extra radio chains (both sides need to have the same, increased number of radio chains to see an increase).
The antennas are fairly small/thin pieces of wire that are not very long, so the antennas don’t need to look like that, but the quantity is useful.
As someone with a telecommunications background who’s taken apart some cheap routers that look like that: the only caveat I’ll add is that the antennas are only useful if they’re actually connected to anything. From a decently trustworthy brand you’re probably fine, but I’ve seen a few where only one or two of the antenna couplings were connected to anything internally.
There’s no shortage of liars and cheats everywhere. I’m unsurprised that a company world either intentionally, or through sheer ignorance, have “antennas” that are little more than aesthetic pieces of plastic.
I believe it’s for beam forming which can be used to improve signal strength in a specific direction.
Some of them are marketing wank, some of them have MIMO channels that need multiple antennas to support independent bands with multiple devices.
1 MIMO channel = 2 antennas, so this router could theoretically have 4 devices communicating bilaterally without interrupting each other.
tell that to the $800 of copper running through my walls.
Hay $800 worth of copper, I found a 1000ft roll of shielded pure copper for $2.11 because someone misplaced the decimal point I know because it was listed for $2.1199 every thing was automated through amazon so they just shipped free shipping to, thank for listening $800 worth of copper, your the best.
you’re
Still cheaper
Wireless tech has improved greatly over the last 20 years. Speed, latency, bandwidth, stability…all generally excellent. 15 years ago I wouldn’t have wanted to use a wireless mouse or LAN connection. Now? NBD. They just work. Still have issues with poor signal in some areas, but mesh range boosters take care of that pretty easily.
Wireless peripheral devices, sure, but if I’m streaming 4K with HD sound then I still want copper.
But what if you’re gaming downstairs and the router is upstairs and then you have to go upstairs for pizza rolls so you take your gaming laptop upstairs and you’re eating right next to the router and so you’re just plugged in and then what if you forgot to turn off the oven and your girlfriend is yelling at you “You’re going to start a fire! Why can’t you remember to turn off the oven? What’s wrong with you?” and then you go back downstairs to finish gaming?
If that happens often enough to be worth 43 times more than the cat cable, then it sounds totally justified to me. But also, what if you got a toaster oven for upstairs? To put next to the router?
What if you used the router as the toaster oven? Tapping_head.gif
I use the microwave for my pizza rolls like a savage. Problem solved.
I eat my pizza rolls cold, like a savage
*Excluding running ethernet cables to every room through the attic, down the walls to wall jacks. Also the cost of the jacks, and the various switches needed for several rooms. And the contractor to do it all.
But hey for like $600 I have cat6a in basically every room so
And the contractor to do it all.
Why wouldn’t you do it yourself?
Disabled, so physically cannot do it, or I would.
Like, in an old house its a massive pain in the ass to run that, but still firmly in DIY territory.
Not everyone is comfortable drilling walls and installing plates, stripping wires, etc. and CAT cables aren’t like simple copper electrical wires.
And not everyone wants to have cables running along their floorboard and up their stairs
And then you still need a wireless router to get Internet on your phone unless you use data at home like a crazy person.
USB-C > Ethernet dongle like a true Network Master.
My PC, laptop, work laptop, are all wired using gigabit. But my laptop on wifi reach 1200Mbps so it’s faster than cable!
Faster than gigabit, but not 2.5 gigabit. Your cables likely support the speed, just your ports and switching hardware are capped at gigabit.
It’s not extremely expensive, but unless you move around a lot of big files, you’re probably getting very diminished returns, even spending less than twice as much for 2.5x speeds.
Impressive, I lose half my speed with the router around the corner.
If you have only one device on Wi-Fi, multiplexing turned off, or especially if you have MU-MIMO support, Wi-Fi can be faster than a single wired connection. It is still higher latency and subject to other drawbacks such as security and power consumption, but of course it offers advantages that can outweigh the disadvantages depending on use case and user needs.
That said, it’s technically not faster than the cable, but rather faster at the data link or network layer. For example, CAT8 physically supports up to 40Gbps, but most consumer and even professional electronics only support up to 2.5Gbps. Only really enterprise level switches can push up to like 100Gbps onto copper, and even then that’s using QSFP transceivers, not RJ-45 connections. Fiber cables regularly push 400Gbps.
Same lol. I get 800Mbps on Cat6, but 1100 on Wifi 6 with one of these fancy expensive 11000ax gaming routers that has all those antennas (antennae?).
Something is wrong there then, because no other ethernet spec is going to cap at 800 Mbps, it’s 10, 100, 1000, 2.5g 5g 10g etc
I know but IDK. Just figured it was an overhead thing. Having a connection that can max out a gigabit ethernet port is still fairly new territory for me.
Ethernet is obviously better but running ethernet around your home can be a pain in the arse
A pain in the arse you only need to do once, and you can hire someone to do it for you for basically the same cost as a couple of the high end wireless routers, so in like 5 years, you break even.
Also, how much have you spent on your computer (s), phone(s), tablet(s), and all your other internet connected devices, and you won’t spend like $500 on something that can run all that stuff simultaneously? Pouring literally thousands of dollars on connected devices, but most won’t pay more than they would for a toaster, to get them on the internet, then pay out the wahzoo for gigabit internet that your crummy d-link router can’t handle, and you wonder why all your fancy gadgets run like shit… It’s a lot like buying a Ferrari to drive on dirt/gravel roads.
I think it’s a little more than $500 to get Ethernet ports installed all around your house. Especially if you need to run through fire breaks and insulation. Will have to wait till a remodel before I can get those installed.
That said, I didn’t skimp on my home networking, even though it’s all wireless. I’ve got 4 WiFi 6 APs on PoE with Cat 6 runs thru the attic. I can get 700 Mbs+ download speeds pretty much anywhere in and around the house.
It could be, depending on where you land on the DIY vs building code spectrum… Also what your local building code details in terms of low voltage cable.
In my experience unless you’re intentionally going through air handling ductwork, CMG is fine, though I would go with CMR at least, just as a matter of safety. I have yet to see a residential home with any fire protection or fire breaks, at all, nevermind where you would think to put them, like between floors and whatnot. The homes in my area are mostly built from timber, so we’re basically living inside a framework of dried out wood, so putting a fire break between wood framed floors where the floor/ceiling shares a set of wooden cross members for support, seems like it would be unnecessary, since the framing of the building is going to conduct the fire between levels.
Ethernet is low voltage, so it’s largely unregulated. The only real regulation is regarding plenum or riser spaces, and the latter is mostly when floors are intentionally or naturally separated in terms of shared fate when it comes to fire. I only see fire breaks in concrete structures, usually apartments or commercial buildings.
YMMV, not every country has the same building codes, so every person reading this will need to do their own research or pay someone who knows.
My point remains, regardless of all this conjecture: even if it’s $2000 or more, this is structure cabling that should service the premise for as long as it continues to stand, which is hopefully many decades. Over 20 years, at $2000 for installation, you’re looking at a cost of around $8.34/mo for the cabling to exist.
Considering people will pay 10x that for Internet service, and the addition of Ethernet in the building will allow them to take full advantage of the internet they’re paying for, I’d call that a bargain.
You will generally run into fire stops in the framing, like you can see here:
https://www.oneprojectcloser.com/fire-stops-fire-blocking-in-studs/
When I ran wires to my office, I had to cut out one section of drywall above it, another below it, and then use a right angle attachment for my drill to go through it. Pull wire through and seal it with fire block foam.
Seems pointless considering the fire stop is made from something flammable.
Its purpose is to slow it down, not stop it. There would be a chimney effect where smoke rises out of the channel and fresh oxygen is allowed to come in from below. The blocks here prevent that from happening.
Oh, I’m not saying it’s not functional in stone capacity. I understand the physics and what is trying to be accomplished with it, but unless it’s done with pretty tight tolerance so any air leakage between the upper and lower spaces is as close to nil as possible, then it’s not going to be super effective.
Preach! I just finished a long DIY remodel and running ethernet to everyroom was less than a $100 in cable and connectors. Obviously it was easier and cheaper for me because I already had a lot of the drywall down.
Either way such a good point you make, people will drop 1k on a phone no questions asked but a few hundred is too much to get the best home upgrade a tech enthusiast could ever ask for.
So far, I’m only £150 down on cable and clips on my rennovation. And this is the decent stuff, AWG23, and double run.
It’ll probably go sideways when I spec up a switch with enough ports, mind…
I could preach all day about this.
I have a simple philosophy: wired when you can, wireless when you have to.
With that being said, doing a site survey for wifi and getting optimal access point locations, then placing Ethernet in ceiling there for said access points, ensures you have good coverage of your space, which then leads into another rant about network hardware and people spending thousands on everything except their router/access points even if they have the structure cables to support such a system…
Then people wonder why their wifi sucks.
I mean, spend a couple hundred one time to get Ethernet run, spend some time on an online ap placement tool and signal estimator for it, and then go buy infrastructure wireless for your home, and spend upwards of $1000 on networking hardware. You’ll get more out of it and it will work for longer than your $1000+ smart phone, or many $1000s laptop that use it almost constantly.
Networking is critical and it should be seamless and blend into the background. You shouldn’t need to mess with it constantly to get it to work. If that’s normal for you, then something is very wrong.
Or if you rent. I could run an Ethernet cable to my office from my router, but it would have to run upstairs and across a few doorways.
Way less so if your home is constructed such that the wireless is borked
That can be an advantage. Some of the enterprise-level tech has trickled down to consumer WiFi in recent years, which includes browsing between multiple access points. With several access points with relatively weak signal, you get signal right where you need it without broadcasting up and down the street.
Nah, wifi is pretty good today. I just dont like the consumer devices like the router shown here. Recently redid my wireless and went with a non wifi router, a poe switch and a few access points, connected through ethernet. I wouldnt dream of going back to the conventional one wifi router. Still use wired for stationary devices I can reach with a cable though… TV, AV, consoles, PC are all wired.
To be honest, I think a lot of Lemmy users are old and yearn for the older technologies simply because they have been more familiar with them than newer ones. They would have used the first gen of a technology, which may not be efficient, and dismiss it altogether, without realising that subsequent generations of that technology improves over time.
I have had that realisation of cognitive bias when I had Bluetooth headphones back in early 2010s. The wireless connection isn’t great and gets cut off every now and then. I dismissed the technology as less efficient than wired earphones. It was over the years with the popularity of airpods that I gave wireless earphones another chance. And honestly, the Bluetooth connectivity vastly improved than I expected and I would not go back to using wired earphones again on regular basis because I don’t have to deal with the wires getting tangled or yanked. I only use wired ones as backup if my wireless earphones went missing or broke.
Sorry to say this to OP, but it seems that you’re being an old man yelling at the clouds. Look, I’m also old and I admit I have had that moment of yelling at the clouds too. We will have that more moments as we age.
I have a similar setup to @PieMePlenty@lemmy.world in regards to my home network and I wouldn’t dream of removing my wifi network. I still consider wired to be superior though it rarely matters at those latencies.
My Windows laptop on wifi:
My Fedora on wired network:
Until the clip breaks off…
You could have 30 clips break and it would still be cheaper.
Wifi 7 is insanely fast to the point where it can easily be just as good as wired ethernet and can even beat a lot of the wired standards except the few latest ones. It’s a good choice for devices where running a cable wouldn’t be very practical, but you need wired level speed and reliability.
wired level speed and
reliability.While WiFi is a lot better nowadays I’ve never seen it reach the reliability of wired networks.
wired will always be better, faster, more reliable, and cheaper
I remember watching a video from Linus demonstrating a WiFi router. I don’t remember if it was WiFi 6 or 7, but any obstacle could cause connection drops.
I don’t know if things have improved since then, but I usually bond WiFi and PowerLine for rooms that Ethernet cannot reach.
Let’s see that ethernet cable do orthogonal frequency-division multiplexing…
Twisted pairs go brrrrrr
Dude I just bought 4 refurbished Linksys MX4200 (tri-band) access points for $80 (total), put on OpenWRT, and built a mesh system. I’m incredibly happy with the result, especially for the price. And, I’ve got wireless bridges all through the house so I can keep some things off the forwarding channels and only in the back haul.
It’s not wired, but it’s close enough and doesn’t require me drilling through all my walls running cable or carving out a space in the house for all of it to coalesce.
Granted, I’m in an area with not a lot of wireless interference…I work in enterprise networking and I’ve had a lot of issues with remote workers on wireless networks that weren’t capable of handling the volume of data that the users were uploading. Sometimes just because there’s too much interference…but a lot of the time it’s because of misconfiguration (either out of ignorance or because the good features, like multicast-to-unicast, are missing), or printer drivers that spam the wireless with multicast whenever the printer is offline (which I’ve seen a surprising amount of times).
If you’re on wireless…multicast is bad, mmmkay? Only “one” device can talk at a time on wireless (barring MIMO shenanigans), and when it’s multicast traffic…it has to get sent at the lowest compatible rates. A lot of routers set this to 6Mbps or even 1Mbps by default. So your nice fancy “1200Mbps” wireless has to slow down a crawl every time your Roku wants to tell Alexa that it’s there. Which is surprisingly often. Scale up for all the internet-of-crap stuff people have and it’s a miracle their wireless works at all.
Oh and I’ve found people with extenders they don’t know about. Ring Chime? Apparently it functions as an 802.11n (only) extender. Huge bottleneck right there. And then it can only be as good as the signal it gets from the next access point.
I’m a nice fellow who provides free internet to all of my neighbors.
It’s a pain sometimes.
I worry about the teenager upstairs, but all the others are old ladies and it doesn’t bother me a bit…until I want to do something serious.
I’m about to (tax time) invest in a router that allows me to control their bandwidth. It’s free, so if 20mbps don’t work for them they can pay for it.
I will open up the kid’s PS5 so he can game. His laptop is getting 10mbps though.
Old ladies rocking 4k to sleep is too much.
They don’t pay for internet so they get the good good on their services. I’m too sorry and antisocial to go deal with it.
Legit would’ve commit crimes for 20mbps growing up. And I was one of the lucky ones too
Who buys a $300 home wifi box? They’re $50-100
deleted by creator
Depends on usage. If you don’t need super fast speeds or low latency, go for cheaper model.
If you need low latency and high speeds (ex. Wireless VR with PC), you need to pay more to get good and stable connection (+ multiple routers as mesh if needed). And more expensive devices have different CPU/RAM which will help you if you have large network + extra security features on.
I spend a lot more money on good Ethernet switches. But at least that works and is easier to manage than Wifi.
Yeah this kinda overlooks a lot of the issues with like… getting a cable somewhere
My house is relatively new (built 2005), and they pulled cat5 for all the telephone lines and just didn’t hook up the extra pairs of wires. Since nobody uses landlines anymore, I rewired most of the outlets for RJ45.
Have pulled a few more wires, including fiber to my main office PC (so I can have a very fast connection to my NAS). Once you learn a few techniques and the way your building is laid out, it’s not that hard.
Yeah, you got to skip over the “getting the wire there” part. If you wanted to replace all that line with cat 5e or cat6 so you can get full duplex gigabit speeds it’d be a much harder task than slapping some rj-45 end onto some old cat 5.
My house was built around the same time and had the same feature. I guess VOIP stuff was beginning to take off and people still had land lines. I can’t imagine much new construction has anything for phones.
Curve ball… I use power line and for my property and in my use case it is not any different to ethernet.
EoP is really cool
$6.99/5’ of cable. A weekend of manual labor running cable through my walls.
Or $300 for something I can set-and-forget.
Decisions, decisions.
$300 in labor is wildly optimistic and true for a simple cable run, maybe
If run probably even a “short” run will typically be at least 20ft. Think, from a wall plate, up an 8ft wall, across a crawl space, down another 8ft wall.
Not all cable runs are simple
It doesn’t even cost that much for a decent wifi AP either.
Given the choice, I’d definitely choose a cable for anything I know will require high internet usage. Wireless is just too slow, even on a 5G connection.
I still remember I once broke my Windows installation (young me had tried dual-booting the Windows 10 beta and my Windows 7 installation). I had to get system restored discs from the manufacturer. It wasn’t particularly tricky to fix, but it took a long time to download those Windows updates after it finished. I noticed an immediate change once I remembered I had an old 30 ft. ethernet cable lying around and plugged it in. (This was maybe 8-10 years ago.)
I’m a cable guy too; it’s just better. But you can’t get quality CAT6 or better cables for $6.99 anymore.
